Stick welding

Welding ABC

Stick welding

February 4, 2024

Applications, equipment, electrodes, and techniques for stick welding

Welding Value

THE BASICS OF STICK WELDING

Stick welding, also known as manual metal arc (MMA) welding refers to a welding method where a filler rod in the electrode holder serves as the welding electrode. The arc burns between the rod and the workpiece.

The difference to other welding methods is that the filler rod that serves as the welding electrode in MMA welding shortens continuously as the welding progresses. In TIG and MIG/MAG welding, the distance of the torch from the workpiece must remain constant at all times. In MMA welding, however, the electrode holder must continuously be brought toward the workpiece to keep the distance between the electrode and the molten weld constant. This presents special challenges for MMA welding.

STICK WELDING APPLICATIONS INCLUDE UNDERWATER WELDING

MMA welding can be used under almost any conditions, and therefore it is a rather universal method in the welding industry. It is commonly used in installation worksites where good reachability is required for welding machines and where work is often done in outdoor environments.

MMA welding is a common welding method for example in welding power plant pipelines and in other pipe welding sites. It is also a welding method favored by hobbyists and small repair shops. It can also be applied in underwater welding, where fillers designed particularly for underwater environments are used.

STICK WELDING MACHINES ARE SMALL AND AGILE

MMA welding requires a power supply, a ground cable, and a welding cable equipped with the electrode holder. There is no shielding gas, as the welding electrode is coated with a material that produces shielding gas and slag over the molten weld pool. Many TIG welding machines are also suitable for MMA welding.

Today’s small inverter power sources further increase mobility and reachability. The power supply can, for example, be connected to a generator with long input cables, taking the welding machine next to the workpiece. The smallest power sources currently weigh only 5 kg (10 lbs).

MMA welding is rather popular in hobbyist use as the only required parts are the power source and the filler material rods. No shielding gas is required, and the devices usually operate with the current obtained from a regular residential power outlet.

Browse Kemppi MMA welding equipment

STICK WELDING USES FIXED-LENGTH ELECTRODES

A welding electrode is a fixed-length, straight welding wire coated with a filler material. The welding electrode has a fixing head with which it is attached to the electrode holder. The other end of the electrode has the ignition head with which the workpiece is stuck to ignite the arc. The quality or trade name of the electrode is indicated near the fixing head in the coating. Usually, also the AWS class ID is included.

The diameter of a welding electrode refers to the diameter of the metal rod inside the electrode. The purpose of the coating on the surface of the metal rod is to protect the welding event from the effects of the surrounding air, to produce slag to support the weld, and to make the creation of the arc easier.

KEEP THE ARC AS SHORT AS POSSIBLE FOR THE PERFECT STICK WELDING TECHNIQUE

Before welding, it is recommended to check the condition of the welding power source, the cables, electrode holder, and the grounding clamp. If the power source has a control panel and remote control, their functionality should also be reviewed. The quality and strength of the welding electrodes must be checked, and they must match the workpiece. The coating on the electrode must be intact.

The welding is started by sharply striking the bottom of the groove with the welding electrode. After this, move the welding electrode back to the beginning without stretching the arc, and move the electrode easily while monitoring the width of the molten weld pool. Move the welding electrode with the handle pointing forward. The boundary of the slag formed is visible after the molten weld. It must be behind the molten weld. The distance of the slag boundary from the molten weld can be adjusted with the welding current and the angle of the electrode holder.

Throughout the welding, concentrate on the length of the arc and keep it as short as possible. The length of the arc increases easily as the electrode decreases in size during the welding. The movement may be somewhat difficult to control at first but it is easy to get accustomed to.

When the welding electrode runs out, one needs to remove the slag from the previous weld and clean it with a steel brush. Ignite the next electrode slightly ahead of the previous weld and then move the welding electrode back to the previous weld and continue with the welding.

Turn off the welding electrode by moving it slightly back to the completed weld and then lifting the electrode straight away from the workpiece.

Welding Value
Author

Welding Value

Welding Value is a corporate blog hosted by Kemppi Oy. Its main purpose is to evoke discussion on the transformation of modern welding, and bring you the latest stories from within the global welding industry told by true experts in their respective fields.

More blog posts

MIG/MAG welding

MIG/MAG welding

MIG welding applications, equipment, and techniques

Welding ABC

TIG welding

TIG welding

Applications, welders, and techniques for TIG welding

Welding ABC

Robotic welding

Robotic welding

Robotic welding applications, systems, and techniques

Welding ABC

How does steel welding benefit from special processes?

How does steel welding benefit from special processes?

Welding mild steels may often be considered a simple task. However, welding these steels has specific characteristics that can make the welding process challenging.

Manual welding, Welding ABC

New Kemppi Robotics Team

New Kemppi Robotics Team

Achieving strategic goals and enhancing customer experience

People

How to choose the MIG/MAG welding torch

How to choose the MIG/MAG welding torch

MIG/MAG welding is one of the most common and versatile welding processes. It is used for various applications, such as automotive, construction, fabrication, and maintenance. However, choosing a suitable welding torch for your job is essential to achieve optimal results.

Manual welding, Welding ABC

Subscribe to our newsletter and be among the first to know the latest from Kemppi.

By subscribing, you agree to receive marketing emails from Kemppi.

The forerunners of arc welding

Kemppi is the design leader of the arc welding industry. Kemppi is the design leader in the arc welding industry. We are committed to boosting the quality and productivity of welding by continuous development of the welding arc and by working for a greener and more equal world. Kemppi supplies sustainable products, digital solutions, and services for professionals from industrial welding companies to single contractors. The usability and reliability of our products is our guiding principle. We operate with a highly skilled partner network covering over 70 countries to make its expertise locally available. Headquartered in Lahti, Finland, Kemppi employs over 650 professionals in 16 countries and has a revenue of 209 MEUR in 2023.

Kemppi – Designed for welders

Copyright © 2024 Kemppi Oy